IEEE 802.3 standards . It was the first attempt to standardize ethernet. Although there was a field of the headend that was defined differently, subsequently there have been successive extensions to the standard that covered the speed extensions (Fast Ethernet, Gigabit Ethernet and 10 Gigabit Ethernet), virtual networks, hubs, switches and different types media, both fiber optic and copper cables (both twisted pair and coaxial).
The IEEE specification for Ethernet is 802.3, which defines what type of cabling is allowed and what are the characteristics of the signal it carries. The original 802.3 specification used a thick 50 ohm coaxial cable, which allows a 10 Mbps signal to be carried at 500 m. Later the possibility of using other types of cables was added: Thin coaxial ; twisted pairs of cables, and fiber optics .
Summary
[ hide ]
- 1 Introduction
- 2 Main standards used in Ethernet
- 1 10Base5
- 2 10Base2
- 3 10Base-T
- 4 10Base-F
- 5 100Base-T4
- 6 100Base-TX
- 7 100Base-FX
- 8 10GBaseT
- 9 Spanning tree
- 3 Source
Introduction
An Ethernet network can transmit data at 10 Mbps over a single baseband channel, usually a coaxial bus or a branched fabric. Cable segments are limited to a maximum of 500 m. Although most manufacturers specify a maximum of 100 stations in each segment, the practical limit may be lower, depending on the utilization.
The maximum number of DTEs (“Data Terminal Equipment” equipment connected to an Ethernet.) In an Ethernet network is 1024; Repeaters can be used to increase the length of the network by connecting multiple segments, but the maximum number of repeaters a signal can encounter is 2.
Main standards used in Ethernet
Note: the different Ethernet standards have a name that follows the general formula xBaseZ. The Base designation refers to “Baseband modulation”, which is the modulation method used. The first number X indicates the speed in Megabits per second over the channel (which is different from the speed available for data, since the “wrappers” are included next to these). The last digit (or letter) Z indicates the maximum cable length in hundreds of meters, or the type of technology. For example, T means twisted pair “Twisted (pairs)”, F fiber optic “Fiber”, and so on.
10Base5
10Base 5 Coaxial Coarse Ethernet
Known as thick wired Ethernet. 10 Mbps, baseband. It can be identified by its yellow wire. Uses thick coaxial cable; the 5 comes from the maximum length of the segment which is 500 m. The cable must be grounded at only one point.
Each station is connected to the cable by means of a transceiver called MAU (“Medium Attachment Unit”) and a drop cable. The connector used in 10Base5 adapters is called AUI (“Attachment Unit Interface”). It looks similar to a 15-pin serial port (DB15).
The transceivers should not be located within 8.2 feet (2.5 meters) of each other, and the drop cable should not exceed 165 feet (50 meters). If a highly flexible drop cable is used this length should be reduced to 41 feet (12.5 meters).
Note: some transceivers have circuits that must be taken into account when counting these lengths; what is called “Equivalent Length”.
10Base2
Known as fine-wire Ethernet whose trade designation is RG-58. 10 Mbps, baseband; uses BNC connectors (“Bayonet Nut connector”). Its maximum distance per segment is 606 feet (185 m), although repeaters can be used to increase this distance as long as the data passes no more than two repeaters before reaching its destination.
The number of DTEs in each segment must not be greater than 30, and they must be separated by a minimum of 1.6 feet (0.5 meters).
Note: in practice this minimum distance must be much greater. The author has found absolutely inexplicable connection failures using this type of cable, which have simply disappeared by keeping this distance (cable length) greater than 4 or 5 meters.
It uses shielded 50 Ohm coaxial cable that must be terminated by 50 Ohm resistive adapters and be grounded at one point. The cable must not be connected to itself forming a ring, and must be connected to the DTE through a “T” adapter, it is not allowed to add an extension to said adapter or connect directly to the DTE by eliminating the “T” adapter. Its best attraction is its price, of the order of 15% of the thick cable.
Note: this type of cable, widely used until recently, has yielded prominence in favor of Base-T installations; currently only recommended for very small installations.
10Base-T
In September 1990, the IEEE approved an addition to the 802.3i specification, generally known as 10BaseT. These lines are much cheaper than the previous coaxial cable, they can be installed over existing UTP (“Unshielded Twister Pairs”) telephone cables [3], and use standard RJ-45 (ISO 8877) telephone connectors, which reduces greatly the installation cost (H12.4.2).
These cables are connected to a series of “hubs”, also known as multi-port repeaters, which can be connected to each other in a chain or forming a tree topology, but the signal path between two DTEs should not include more than five segments, four repeaters (including optional AUIs), two transceivers (MAUs) and two AUIs.
10 Mbps, baseband, Category 3, 4 or 5 2-pair UTP telephone cable, with a characteristic impedance of 100 +/- 15 ohms at 10 Mhz [4]; It must not exceed 328 feet (100 m).
When a network contains five segments and four repeaters, the number of coaxial segments must not be greater than three, the rest must be links with DTEs (this is known as the 5-4-3 rule). In other words: Between any pair of stations there should be no more than 5 segments, 4 repeaters and 3 hub-hub connections. If fiber optic segments are used, they should not exceed 1640 feet (500 meters).
When a network contains four segments and three repeaters using fiber optic links, the segments must not exceed 3,280 feet (1000 meters).
10Base-F
10 Mbps, baseband, fiber optic cable. Maximum length of the segment 2000 meters.
100Base-T4
Fast Ethernet 100 Mbps, baseband, using category 3, 4 or 5 twisted pair of 4 pairs. Maximum distance 100 m.
100Base-TX
Fast Ethernet 100 Mbps, baseband, uses Category 5 twisted pair. Maximum distance 100 m.
100Base-FX
100 Mbps Fast Ethernet using fiber optics. Maximum length of the segment 2000 meters.
10GBaseT
In June 2006 the 10GBaseT standard was approved. As is clear from its name, it refers to connections of 10 Gbit per second (10,000 Mbps) with a maximum length between Hubs or repeaters (segment) of 100 m. However, as of the date of publication of the standard, no standardized cables met the requirements. Category 6 was initially adopted for 55 meter segments but had to be reduced to 37 m. Category 7 cable is expected to fully meet the requirements of the new specification.
Spanning tree
The spanning tree is a type of connection associated with the IEEE 802.3 standard that does not require stations on the network to keep track of addresses, which implies a lower cost for each NIC.




