Herbicide . A plant protection product used to kill unwanted plants . Selective herbicides kill certain targets while sparing the crop relatively unscathed. Some work by interfering with weed growth and are often based on plant hormones . Herbicides used to clear large fields are nonselective and kill every plant they come into contact with.
What are herbicides?
Herbicides are chemical substances that can kill or suppress the growth of certain unwanted plants, considered weeds, which in turn consist of any unwanted plant that grows in a given area and is capable of interfering with the development of another desired plant .
Herbicides, like other pesticides , are tested and recommended specifically for certain uses. This means that they are suitable for certain crops that tolerate them perfectly and certain weed species that are susceptible.
Herbicide classification
- Herbicides that are applied to the soil.
- Herbicides that are applied to the leaves.
- For its action on different types of plants
- Selective herbicides: These act on certain plants belonging to a certain botanical family, and do not exert control over other plants belonging to other botanical families. For example: 2,4-D acts on broadleaf weeds and does not affect fine leaves (grasses), Clorimuron ethyl (Classic) controls broadleaf weeds present in soybean crops, without affecting said crop.
- Non-selective or total herbicides: They control all types of weeds, acting on any plant species; therefore, they are not selective. For example: Glyphosate (Round up) for the control of fine leaves and some broad leaves, 2,4-D controls broad-leaf weeds, it does not present selectivity for any weeds and broad-leaf crops.
- Due to its mode of action on plants
- Contact herbicides: These herbicides only affect the parts of the weeds that have been covered by the product, so it is important to thoroughly wet the weeds you want to control. The roots of the weeds are not affected by these herbicides and may sprout again. For example, Paraquat ( Gramoxone ), Lactofen ( Cobra ), Bentazon ( Basagran ).
- Systemic or internal-acting herbicides: Once applied to weeds, they are absorbed and travel through all the organs of the weed, including the roots. For example, 2,4-D, Glyphosate (Round up), Setoxydim ( Poast ), Cletodín (Select).
- By the opportunity in which they are applied
- Pre-plant herbicides: These are applied before sowing or establishing the crop, to eliminate existing weeds, as well as germinating weed seeds and vegetative propagation organs. For example, Sulfentrazone (Boral SC).
- Pre-emergence herbicides: These are applied after sowing the crop, before germination of the crop and/or weeds. They destroy small weed seedlings after they have germinated. For example, Imazaquim (Scepter), Flometsulam (Preside), Pendimetalim (Herbadox).
- Post-emergence herbicides: These are applied after the germination of the crop and weeds. It is recommended to do so when the weeds are in their initial stage of development. The ideal stage of application is for fine leaves up to the 4th tiller and for broad leaves up to 4 true leaves. Late application is when weeds are more developed.
Application of herbicides
Through the application of herbicides, the development of weeds present in a given area before planting a crop , or that are present in a crop competing with it, is controlled.
Conditions for efficient application of herbicides
Whatever herbicide is applied, it requires extensive technical knowledge and compliance with certain established standards, such as environmental factors, application schedule and technology, and weed size, so that this practice is effective and the objective of the application itself is met, which is to satisfactorily control or dry out the weed or crop with the herbicide.
Environmental factors
Environmental factors, such as temperature and relative humidity, are very important for the application of herbicides, because they determine the type of reaction of plants to external stimuli or treatments.
The environmental factors that must be considered and respected for the efficient application of herbicides in order to obtain good results are the following:
- Temperature: It should be applied at a temperature below 30º C. There are herbicides that require a certain minimum temperature for their rapid action inside the plant, such as glyphosate, which, when applied at a temperature below 15º C, delays its action and consequently its effect on the plant.
Temperature can influence the results of certain herbicides, mainly systemic herbicides such as Metsulfuron methyl (Ally), Glyphosate (Roud up), 2,4-D, etc. Their efficiency is reduced when they are applied at average daily temperatures below 12°.
- Relative humidity: The recommendation is to apply with relative humidity above 60% to avoid drying of the spray droplets and ensure that they reach the target in their entirety. Another drawback is that with low relative humidity, the plant is in a state of stress. High temperatures (greater than 30º C) and low humidity (less than 60%) favor the loss of the product through evaporation. There are adjuvants that help to avoid this drawback but this means an increase in the cost of application.
- Wind speed: It should not exceed 10 kilometers per hour. A practical way to determine this is by using a gas lighter; once in the place where the application will be made, proceed to light it with a large flame; if it does not go out, the wind speed is adequate; if the flame goes out, the wind speed is not appropriate for making the application.
It is important to always consider wind speed when applying herbicides, thus ensuring that the applied product reaches the target (efficient application) and is not deposited in other unwanted areas due to drift, causing damage to other crops on the same property or that of a neighbor, avoiding inconvenience and disruption due to poor application.
Drift is the transport of spray droplets to other, undesirable areas, away from the application site. The distance of drift depends on the size of the application droplets and the wind speed.
- Possibility of rain: It is recommended not to apply when imminent rains are approaching, because the applied product can be washed away by rainwater, with the possibility of infiltrating the subsoil or reaching water courses, contaminating them. Each herbicide product has a time required for its absorption by the plant, which is indicated on the label of the herbicide container; and if rain occurs before this time, the product is not absorbed by the plant and is washed away by rainwater.
Application schedule
It is recommended to apply during the first hours of the day up to 10:00 am and in the late afternoon from 5:00 pm (summer time), avoiding the hottest hours of the day between the times mentioned. In addition, during this time, the ideal environmental conditions, mentioned above, for application normally occur. Respecting this time ensures that the plants to be controlled are vigorous and active, which is essential for the absorption of the herbicide by the plant and achieving good results.
Herbicide dosage
The dosage of herbicides is presented in units of weight or volume per surface unit, for example kg or liters of herbicide per hectare. It must be ensured that the dose applied is the one recommended on the product label, since if it is underdosed there will be no response and if it is overdosed not only will the weeds be damaged but also the plants that are to be preserved.
Application of different herbicides
Accent is a systemic herbicide for the post-emergence control of annual and perennial grass weeds, and most annual broadleaf weeds.

