As it is well known, the controls of the Nintendo Wii are synchronized to the console by means of infrared , which makes them a practical and easy-to-use tool. However, there are times when these controls become out of sync and that is where the problems begin. If this is the situation you are going through right now, don’t worry. We have the solution for you!
Index( )
- How can you check if control binding was done with the console?
- What can you do to properly sync your remote if it doesn’t finish as usual?
- Restart Wi-Fi signal
- re-synchronize
- Check the status of your batteries
- Repair or replace your remote
- Check the status of your console
How can you check if control binding was done with the console?
The connection of controls in Nintendo consoles has always been a popular topic and the Wii remote control does not escape this. To be able to play, the first thing you should do is verify if the connection of the control with the console has been carried out correctly.
For this you only have to press the power button on the Wii control, if doing so the console turns on it is because the connection is in perfect condition. If, on the other hand, the console does not turn on, it means that it is possibly having connection problems.
What can you do to properly sync your remote if it doesn’t finish as usual?
When the Wii Remote does not automatically sync with the console, it must be done manually . There are several ways to make the connection between the two reappear, such as restarting the WiFi signal, checking the batteries or checking the status of the console; If none of these options work, you should contact Nintendo Customer Service to report the problem.
Restart Wi-Fi signal
Hard resetting everything is always something that tends to work when your console has been on for a long time or has been abruptly turned off at some point, this refreshes the signal and the connection.
Therefore, turn off the electrical network of your console and also that of your WiFi, leave it off for 30 seconds and then reconnect everything and turn on the console , if the problem is solved, leave everything as it is. In case you continue to have problems, try another solution method.
re-synchronize
If the problem continues, you can choose to sync the controls again. This is an option that Nintendo added for just such cases where the Wii Remote stops working . To do so, you just have to follow the steps that we show you below, it is a simple process to perform and quite fast.
- The first thing you have to do is turn off your console, wait 15 seconds and turn it back on.
- Wait until the ‘Health and Safety’ warning appears. At this point you should open the SD card slot on the front of the console, while simultaneously holding down the red ‘Sync’ button for 15 seconds.
- On the Wii Remote, remove the battery cover and press the red ‘Sync’ button located there.
- Now press both buttons, both the one on the controller and the one on the console and wait for both to pair, this can take approximately 10 seconds.
- If you have other controls that you want to sync, just follow the same process.
Check the status of your batteries
Checking the status of the batteries is important because aside from it being one of the most common reasons controllers stop working, it’s an option you don’t think of so quickly. These controls use 2 AA type batteries which can be exchangeable or rechargeable (this is up to you).
Nintendo explains that the batteries have a duration time of 60 hours if used normally. This time is reduced to 25 hours if used as a pointer.
If you have not consumed this time then remove the batteries and put them back, otherwise the hours have been exceeded then the best option is to recharge them or replace them with new ones. It is necessary that after changing the batteries, the synchronization process that we explained previously is carried out again.
Repair or replace your remote
If you have tried all the options and nothing works anymore, then it is time to replace your remote control. Like all of them, these have a useful life time and this is influenced by the way in which you have used them since you have your console. The good thing is that they have lowered their price quite a bit and you can easily get them in any store.
We recommend that before exchanging your control you contact Nintendo’s customer service and wait for a response from them, which may possibly solve your problem and thus avoid spending unnecessary money. necessary. While you wait for an answer you can choose to find out the way in which video games can be created and then used on your console .
Check the status of your console
If all options have already been tried and the controllers still fail to sync then it is most likely the console that is failing. To get rid of doubts, try your controls with a friend’s console and if they work then the problem is in your Nintendo.
You can take it to authorized places for repair and if it does not work, the solution is to opt for a new console. At this point, the only thing we can recommend to keep you entertained is to download some good games to play on your Android and thus the wait for your console will be less long.